Description
E14 illuminant compatible with ZigBee gateways such as Philips Hue®, Osram Lightify®, Ikea Tradfri®, Amazon Echo Plus
This new generation of ZigBee E14 bulbs work with the ZigBee 3.0 standard and are thus compatible with the most common gateways. You can adjust and mix different colors of RGB shades with this light source.
In addition, the color temperature can be set between 2700 Kelvin and 6500 Kelvin. Depending on the ZigBee controller, using both techniques, you can set color saturation to use more color options (pastel colors).
- Switch between multiple lighting modes with your choice.
- Rich lamplight atmosphere, give you more pure and fresh sense, available in dimmer & night light mode options
- Brightness and colour temperature dimmable & adjustable from warm white 3000K to cool/cold white 6500K
- Customize your colourful life, 16 million color saturation changes, make life full of beauty
- Home or Away lighting mode, to remote control the smart LED bulb even away from home, to ensure the safety of your home
Rainbow of colors
The color temperature of the light is from 2000k to 6500k (RGB+CCT). More than 16 million color choices and all of them are dimmable. You can easily set the color to suit your mood with dimmable brightness. Brighten up the room or create a relaxing environment by dimming the light.
Installation
1.Turn off the Power.
2.Plug in the bulb.
3.Now you can connect it with the gateway.
Connection with Gateway:
1.Start the device searching on the ZigBee Light Link Gateway, it could take some time.
If the Gateway does not find the device, switch off/on the gateway and try again or
3.The Gateway found your device and you can assign it to the different rooms/zones/groups.
4.Now you can use the device.
Reset
1.Switch on your device.
2.Now switch off and on within 2 seconds.
3.Repeat off/on four times.
4.Reset is done when the device is switched on in the fifth time and the light stays on after blinking 4 times.
Link & unlink with 2.4GHZ RF Remote Control
How to Link
1. Within 3 seconds after power on, click the “on” button of the group to conduct code matching, and the LED lights turns green, indicating successful code matching.
2. Long press the “off” button of the remote control to enter the night light mode, and the brightness and colour can still be adjusted at this time.3. Long press the small moon key to enter the 60 seconds delay shutdown state.4. Long press M key to enter automatic mode.
How to unlink
1. If the LED is still connected to the ZigBee gateway, long press the “on” button on the remote control within 3 seconds after power on or press the button for 5 times continuously, the light will flash for 5 times in the current colour.2. If the LED is not connected to the ZigBee gateway status, on press the “on” button on the remote control within 3 seconds after power on or press the button for 5 times continuously, then the LED light will be fully bright and flashing for 5 times.
Link & unlink with 2.4GHZ RF Remote Control
How to Link
- Within 3 seconds after power on, click the “on” button of the group to conduct code matching, and the LED lights turns green, indicating successful code matching.
- Long press the “off” button of the remote control to enter the night light mode, and the brightness and colour can still be adjusted at this time.
- Long press the small moon key to enter the 60 seconds delay shutdown state.
- Long press M key to enter automatic mode.
How to unlink
- If the LED is still connected to the ZigBee gateway, long press the “on” button on the remote control within 3 seconds after power on or press the button for 5 times continuously, the light will flash for 5 times in the current colour.
- If the LED is not connected to the ZigBee gateway status, on press the “on” button on the remote control within 3 seconds after power on or press the button for 5 times continuously, then the LED light will be fully bright and flashing for 5 times.
